Be tong mac 100 da 2x4


Recent Posts

All parts and accessories added to the vehicle must be genuine Polaris Industries Inc. Always remove the ignition key when the vehicle is not in use. WARNING After any overturn or accident, have a qualified service dealer inspect the entire vehicle for possible damage, including but not limited to brakes, throttle and steering systems. If any decal becomes illegible or comes off, contact your Polaris dealer to purchase a replacement.

Replacement safety decals are provided by Polaris at no charge. The part number is printed on the decal.

Cap phoi be tong mac 100 da 2x4

To prevent serious injury, do not operate vehicle with guard removed. Do not modify engine or clutch. Doing so can cause part failure, possible imbalance, and excessive engine RPM, which can result in serious injury or death. Reduce speed and allow greater distance for braking when carrying cargo.

This may cause severe drive shaft and clutch damage.

ATV riding requires special protective clothing for comfort and to reduce the chance of injury. Helmet Your helmet is the most important piece of protective gear for safe riding.

Historical Event but No Press Coverage? 20th Anniversary Million Man March. – #OCCUPYINGYOURMINDSET

A helmet can prevent a severe head injury. S Always exercise extreme caution whenever handling gasoline. S Always refuel with the engine stopped, and outdoors or in a well ventilated area. S Do not smoke or allow open flames or sparks in or near the area where refueling is performed or where gasoline is stored. Your ATV is not equipped with highway-approved lights. Use caution and drive at reduced speeds in conditions of reduced visibility such as fog, rain and darkness. Page 38 Electrical Switches 3.

Much more than documents.

Its purpose is to provide the operator with a quick means of engine shutdown in case of an emergency. To stop the engine, slide the stop switch either right or left to the OFF position. If the throttle cable should stick in an open position when the operator releases the throttle lever, the engine will stop, and power to the rear wheels will cease.

See page for the part numbers of Polaris products. The front and rear brakes are hydraulically activated disc type brakes that are activated by only one lever. Always test brake lever travel and master cylinder fluid level before riding. Always check to be sure the parking brake is disengaged before operating. Setting the Parking Brake 1. Squeeze and release the brake lever 1 two or three times, then squeeze and hold. Use caution when applying the auxiliary brake.


  1. ĐỊNH-MỨC-CẤP-PHỐI-BÊ-TÔNG (1);
  2. download mac os x lion free iso.
  3. convert youtube videos to mp3 on mac.

Do not aggressively apply the auxiliary brake when going forward. The rear wheels may skid and slide sideways, causing loss of control and serious injury or death.

Máy trộn tời đổ bê tông xi măng tự động 1 bao đổ sàn nhà

Page Fuel Valve Choke The choke assists in starting a cold engine. Refer to the engine starting procedure on page 52 for correct choke and throttle settings during starting. Fuel Valve The fuel valve 1 is located on the left side of the vehicle on the side panel.

champleasyswaipan.tk

Sony hdr cx190 software for mac

It has three positions: OFF: For vehicle storage and when transporting. Page Recoil Starter The recoil starter is located on the right side of the machine. Polaris 4-cycle engines are equipped with automatic decompressors. This makes recoil starting possible by reducing the amount of compression during starting. The decompressor senses when the engine is spinning fast enough to start and restores compression when running. Engage the AWD when the rear wheels lose traction.

Page 48 Instrument Cluster Magnum Your ATV is equipped with an instrument cluster that senses vehicle speed from the right front wheel. The instrument cluster measures distance in miles as well as hours of operation. If this occurs take the ATV to your Polaris dealer for proper diagnosis. NOTE: All segments of the rider information center will light up for 2.

UNLIMITED BOOKS LIBRARY

When your vehicle leaves the factory, this feature is turned off. Please return your ATV to your dealer for all major repairs. To enter the diagnostics mode: 1. Turn the key switch off and wait 20 seconds. No single action on your part is as important as following the procedures for a proper break-in. Never run an engine in an enclosed area. Place the transmission in PARK and lock the parking brake.

Page Starting A Warm Engine Water in the bottom of the tank can lead to engine damage and must be drained. Water accumulation increases as outside temperature decreases. See your Polaris dealer for engine heater kits, which provide quicker warm-ups and easier starting in colder weather.

Sit upright with both feet on the footrests and both hands on the handlebars. Start the engine and allow it to warm up, then shift the transmission into gear. Check your surroundings and determine your path of travel. This means that the wheel on the outside of the turn must travel a greater distance than the inside wheel when turning and the inside tire must slip traction slightly.

Always read and understand the load distribution warnings listed on the warning labels, and never exceed the specified weights. When operating over rough or hilly terrain, reduce speed and cargo to maintain stable driving conditions. Slow down when entering slippery areas.

Sunshine Coast News - UBC Library Open Collections

Maintain a high level of alertness, reading the trail and avoiding quick, sharp turns which can cause skids. Always travel straight uphill. Keep both feet on the footrests. Transfer your weight forward. Proceed at a steady rate of speed and throttle opening. Avoid crossing the side of a hill when possible. Sidehilling can be the most dangerous type of driving encountered and should be avoided if at all possible. Proceed directly downhill. Transfer your weight to the rear of the vehicle. Slow down.

be tong mac 100 da 2x4 Be tong mac 100 da 2x4
be tong mac 100 da 2x4 Be tong mac 100 da 2x4
be tong mac 100 da 2x4 Be tong mac 100 da 2x4
be tong mac 100 da 2x4 Be tong mac 100 da 2x4
be tong mac 100 da 2x4 Be tong mac 100 da 2x4
be tong mac 100 da 2x4 Be tong mac 100 da 2x4
be tong mac 100 da 2x4 Be tong mac 100 da 2x4
be tong mac 100 da 2x4 Be tong mac 100 da 2x4
Be tong mac 100 da 2x4

Related be tong mac 100 da 2x4



Copyright 2019 - All Right Reserved